Unistrut P2751N EG - Loop Trolley w/ Nylon Wheels, Design Load 20 Lbs, EA / Box (25)

Product Details

Unistrut Buffalo is a division of Eberl Iron Works, Inc.

STANDARD DIMENSIONS

Standard Dimensions for 1-5/8" (41.3 mm) width series channel (Unless otherwise specified in Unistrut General Engineering Catalog):

Hole Diameter: 9/16" (14.3 mm)

Hole Spacing - From End: 13/16" (20.6 mm)

Hole Spacing - On Center: 1-7/8" (47.6 mm)

Width: 1-5/8" (41.3 mm)

Thickness: 1/4" (6.4 mm) with steel meeting or exceeding ASTM A1011 SS GR 33, or 0.220" (5.6mm) with steel meeting or exceeding ASTM A1011 HSLAS GR 45

Note: When used for mechanical supports, load capacities of brackets, fittings and other supporting elements should be in compliance with the American Standard Code for Pressure Piping. Clamps are designed to be used with W, M, S & HP Shape beams, Standard C & Misc. MC Channels, Angles & Structural Tees. Clamps must be used in pairs where indicated. For beam clamps with HG finish, standard hardware is EG finish. For optional stainless steel hardware, please contact the factory for availability.

MATERIAL

Fittings, unless noted, are made from hot-rolled, pickled and oiled steel plates, bar, strip or coil, and conform to one or more of the following specifications: ASTM specifications A575, A576, A635, A1011 SS GR 33, A1011 HSLAS GR 45 or A36. All fittings meet or exceed physical properties of ASTM A1011 GR 33. The pickling of the steel produces a smooth surface free from scale. Many fittings are also available in stainless steel, aluminum and fiberglass. Consult factory for ordering information.

FINISHES

Fittings are available in:

• Green Powder Coat (GR), conforming to commercial standards for Powder Coating
• Electro-galvanized (EG), conforming to ASTM B633 Type III SC1
• Hot-dipped galvanized (HG), conforming to ASTM A123 or A153
• Plain (PL)
• Unistrut Defender (DF), conforming to ASTM A1059 or A1046

*** Perma Green finish is a commercial grade finish, and as such scuffs and scratch marks are to be expected. If a flawless finish is desired, it is recommended to apply a matching touch up paint ***

APPLICATION

All parts drawings illustrate only one application of each fitting. In most cases many other applications are possible. The channels shown in the illustrations are P1000, 15⁄8" square, except where noted otherwise. All 9⁄16" diameter holes use 1⁄2" x 15⁄16" hex head cap screws and 1⁄2" nuts – P1010, P3010, P4010 or P5510 – depending on the channel used. Nuts and bolts are not included with the fitting and must be ordered separately.

DESIGN BOLT TORQUE

 
SET SCREW TORQUE

DIMENSIONS

Imperial dimensions are illustrated in inches. Metric dimensions are shown in parenthesis or as noted. Unless noted, all metric dimensions are in millimeters and rounded to one decimal place.

DESIGN LOAD

Design load data, where shown, is based on the ultimate strength of the connection with a safety factor of 2.5, unless otherwise noted.

BEAM CLAMPS

Clamps are designed to be used with W, M, S and HP Shape beams, Standard C and Miscellaneous MC Channels, Angles and Structural Tees. Clamps must be used in pairs mounted in opposite directions where indicated. For beam clamps with HG finish, standard hardware is EG finish. For optional stainless steel hardware, please contact the factory for availability.